Effect of Abrasive Grain Geometry on Cutting Forces in Grinding
| Authors: Voronov S.A., Weidong Ma | Published: 14.09.2017 |
| Published in issue: #5(116)/2017 | |
| DOI: | |
| Category: Mechanical Engineering and Machine Science | Chapter: Technology and Equipment of Mechanical and Physical Processing | |
| Keywords: abrasive grain, finite element method, stress-strain state, temperature, grinding, cutting forces, micro-cutting | |
Methodological Approach and Software for Assessing Loads, Defects and Degradation of Mechanical Characteristics in Structural Materials, Based on Processing Experimental Data
| Authors: Chernyatin A.S., Razumovskiy I.A. | Published: 14.09.2017 |
| Published in issue: #5(116)/2017 | |
| DOI: | |
| Category: Mechanical Engineering and Machine Science | Chapter: Inspection and Diagnostics in Mechanical Engineering | |
| Keywords: finite element method, optical digital methods of displacement investigation, indentation method, optimisation problem, load and defect assessment | |
Automated Algorithm for Nonlinear Optimization of Mechanical Pre-Processing
| Authors: Galkin M.G., Smagin A.S. | Published: 05.12.2017 |
| Published in issue: #6(117)/2017 | |
| DOI: | |
| Category: Mechanical Engineering and Machine Science | Chapter: Manufacturing Engineering | |
| Keywords: automation, technological process, optimization of cutting conditions, Lagrangian multiplier method | |
New Technologies for Surface Layer Quality Improvement in Cutting Fibrous Polymer Composite Materials
| Authors: Yaroslavtsev V.M. | Published: 05.12.2017 |
| Published in issue: #6(117)/2017 | |
| DOI: | |
| Category: Mechanical Engineering and Machine Science | Chapter: Technology and Equipment of Mechanical and Physical Processing | |
| Keywords: innovative technology, machining, polymer composite materials, surface layer quality, hairiness of the surface, thermo-mechanical effects, thermal destruction | |
Identification of Mathematical Model Parameters of Control Unit of Autonomous Single-Stage Electro-Hydraulic Control Actuator
| Authors: Belonogov O.B. | Published: 09.02.2018 |
| Published in issue: #1(118)/2018 | |
| DOI: | |
| Category: Mechanical Engineering and Machine Science | Chapter: Machine Science | |
| Keywords: static characteristics, frequency response characteristics, steering machine, parameter identification method | |
On Replacement of Radiographic Film with Digital Detectors
| Authors: Zhukov A.D., Galkin D.I., Ivanayskiy E.A. | Published: 09.02.2018 |
| Published in issue: #1(118)/2018 | |
| DOI: | |
| Category: Mechanical Engineering and Machine Science | Chapter: Manufacturing Engineering | |
| Keywords: digital radiography, spatial basic resolution, duplex wire image quality identificator, unsharpness, contrast ratio, replacement of traditional radiography with digital detectors | |
Determining the Optimal Sphere of Аpplication of Hybrid Rolling Bearings
| Authors: Lavrentev Yu.L. | Published: 09.02.2018 |
| Published in issue: #1(118)/2018 | |
| DOI: | |
| Category: Mechanical Engineering and Machine Science | Chapter: Machine Science | |
| Keywords: ceramics, hybrid bearings, contact stresses, bearing fatique life, aircraftengine | |
Efficiency of Strain Hardening of Carburized Gear Wheels From Steel 13Х3НВМ2Ф-Ш
| Authors: Pakhomova S.A., Ryzhova M.Yu. | Published: 09.02.2018 |
| Published in issue: #1(118)/2018 | |
| DOI: | |
| Category: Mechanical Engineering and Machine Science | Chapter: Technology and Equipment of Mechanical and Physical Processing | |
| Keywords: gear wheels, heat-resistant steel, strain hardening, gas carburization, hardness, contact fatigue | |
Computing Contact Forces Between a Deformable Object and Gripper Links of a Manipulator
| Authors: Leskov A.G., Seliverstova E.V. | Published: 14.06.2018 |
| Published in issue: #3(120)/2018 | |
| DOI: | |
| Category: Mechanical Engineering and Machine Science | Chapter: Robots, Mechatronics, and Robotic Systems | |
| Keywords: grasp, deformable object, simulation, automatic object grasping, contact forces, grasp planning, Schunk WSG50, contact forces | |
Ensuring Thread Precision During Milling at the Tool Design Stage
| Authors: Malkov O.V. | Published: 14.06.2018 |
| Published in issue: #3(120)/2018 | |
| DOI: | |
| Category: Mechanical Engineering and Machine Science | Chapter: Technology and Equipment of Mechanical and Physical Processing | |
| Keywords: programmable radius, thread, thread mill, thread milling | |