REFERENCES
[1] Popov E.A. Osnovy teorii listovoy shtampovki [Fundamentals of the theory sheet-
metal stamping]. Moscow, Mashinostroenie Publ., 1977. 278 p.
[2] Romanovskiy V.P. Spravochnik po kholodnoy shtampovke [Handbook of cold
stamping]. Leningrad, Mashinostroenie Publ., 1979. 520 p.
[3] Zubtsov M.E. Listovaya shtampovka [The sheet-metal stamping]. Leningrad,
Mashinostroenie Publ., 1980. 432 p.
[4] Trishevskiy I.S. Profilirovannye profile [The profiled profiles]. Moscow, Metallurgiya
Publ., 1972. 220 p.
[5] Lukashkin N.D., Kokhan L.S., Morozov Yu.A., Punin V.I. Improvement of equipment
for the bent profiles production.
Novye tekhnologii
[New technologies], 2003, no. 5–6,
pp. 26–30 (in Russ.).
[6] Lukashkin N.D., Kokhan L.S., Punin V.I., Morozov Yu.A. Gibka profiley na pressakh
i stanakh [Profiles bending on presses and mills]. Moscow, MGVMI Publ., 2005.
140 p.
[7] Storozhev M.V., Popov E.A. Teoriya obrabotki metallov davleniem [Theory of metal
forming]. Moscow, Mashinostroenie Publ., 1971. 424 p.
[8] Feodos’ev V.I. Soprotivlenie materialov [Theory of structural resistance]. Moscow,
MGTU im. N.E. Baumana Publ., 2010. 592 p.
[9] Punin V.I. Analysis of change in strip geometry under condition of profile bending.
Vestn. Mosk. Gos. Tekh. Univ. im. N.E. Baumana, Mashinostr.
[Herald of the Bauman
Moscow State Tech. Univ., Mech. Eng.], 2012, no. 2, pp. 88–95 (in Russ.).
[10] Punin V.I., Doktorov M.E. Variation of billet parameters during bending
Technologiya
Metallov
[Technology of metals], 2011, no. 3, pp. 1–16 (in Russ.).
[11] Tselikov A.I., Tomlenov A.D., Zyuzin V.I., Tret’yakov A.V., Nikitin G.S. Teoriya
prokatki. Spravochnik [The theory of Rolling. Handbook]. Moscow, Metallurgiya
Publ., 1978. 335 p.
Статья поступила в редакцию 11.04.2013
Пунин Владимир Иванович — канд. техн. наук, технический директор ООО “Рол-
тяжмаш”. Автор более 40 научных работ и 20 изобретений в области гибки метал-
лических профилей, изготовления труб.
ООО “Ролтяжмаш”, Российская Федерация, 107113, Москва, Сокольническая пл.,
д. 4а.
Punin V.I. — Cand. Sci. (Eng.), chief technology officer of the OOO “Roltyazhmash
(RTM)” [JSC “Roltyazhmash”]. Author of more than 40 publications and the creator of
more than 20 inventions in the field of steel sections bending, pipe production.
OOO “Roltyazhmash”, Sokolnicheskaya pl. 4a, Moscow, 107113 Russian Federation.
ISSN 0236-3941. Вестник МГТУ им. Н.Э. Баумана. Сер. “Машиностроение” 2014. № 5 97
