Electric energy generation at compressor stations using gas-turbine heat recovery plants
Authors: Tumashev R.Z., Mikheev S.S., Kunikeev B.A. | Published: 14.02.2016 |
Published in issue: #1(106)/2016 | |
DOI: | |
Category: Power Engineering | Chapter: Turbomachines and Combination Turbine Plants | |
Keywords: heat recovery, gas-turbine plant, efficiency, electrical energy, pressure boost, optimal parameters |
Verification of numerical simulation of air flow in axial compressor stage
Authors: Komarov O.V., Sedunin V.A., Blinov V.L., Serkov S.A. | Published: 14.02.2016 |
Published in issue: #1(106)/2016 | |
DOI: | |
Category: Power Engineering | Chapter: Turbomachines and Combination Turbine Plants | |
Keywords: mesh sizes of computational domain, axial flow compressor, CFD calculations, experimental study, aerodynamic performance, compressor blade airfoil |
Solving inverse time-dependent external heat conduction problems for combustion chamber surfaces of internal combustion engine
Authors: Ivashchenko N.A., Neuburg L.R., Kavtaradze R.Z., Aliev I.N. | Published: 14.02.2016 |
Published in issue: #1(106)/2016 | |
DOI: | |
Category: Power Engineering | Chapter: Heat Engines | |
Keywords: inverse problem, heat conductivity, boundary condition, heat flux sensor |
Test results of common rail fuel injection system for diesel engines with fuel pressure up to 3000 bar
Authors: Dunin A.Yu., Dushkin P.V. | Published: 14.02.2016 |
Published in issue: #1(106)/2016 | |
DOI: | |
Category: Power Engineering | Chapter: Heat Engines | |
Keywords: fuel equipment, Common Rail injection system, Common Rail fuel injector, ultra high pressure injection |
Computational method for powerful non-adjustable volume hydraulic drive with several volume hydraulic motors
Authors: Nikitin O.F. | Published: 14.02.2016 |
Published in issue: #1(106)/2016 | |
DOI: | |
Category: Power Engineering | Chapter: Hydraulic Machines and Hydropneumatic units | |
Keywords: non-adjustable volume hydraulic drive, hydraulic motor, efficiency, power, pump supply, discharge pressure, pressure losses |
Effect of the Partial Heat Insulation of the Diesel Engine Combustion Chamber on Heat Transfer into the Cooling System
Authors: Onishchenko D.O., Pankratov S.A. , Smirnov A.Yu. | Published: 12.06.2016 |
Published in issue: #3(108)/2016 | |
DOI: | |
Category: Power Engineering | Chapter: Heat Engines | |
Keywords: diesel, heat insulation, combustion chamber, cooling system, zirconium dioxide, heat transfer |
Studying the Strength Characteristics of Axial Compressor Blades
Authors: Sedunin V.A., Nuss A.S., Serkov S.A. | Published: 12.06.2016 |
Published in issue: #3(108)/2016 | |
DOI: | |
Category: Power Engineering | Chapter: Vacuum, Compressor Technology, and Pneumatic Systems | |
Keywords: axial compressor, calculation of strength, verification, the natural frequency, computational mesh size, structural computations, mechanical characteristics, stress-strain state, mode shapes, Campbell diagram, centrifugal force, shank, maximum voltage |
Partial Homogenization Effect of the Combustion Process on the Environmental Performance of Diesel
Authors: Kavtaradze R.Z., Zinovev I.A. | Published: 11.08.2016 |
Published in issue: #4(109)/2016 | |
DOI: | |
Category: Power Engineering | Chapter: Heat Engines | |
Keywords: diesel, repeated injection, mixture homogenization, nitrogen oxides, soot |
Effective Range of Gas Pressure at the Suction Side of the Turbomolecular Vacuum Pump
Authors: Demikhov K.E., Ochkov A.A. | Published: 19.10.2016 |
Published in issue: #5(110)/2016 | |
DOI: | |
Category: Power Engineering | Chapter: Vacuum, Compressor Technology, and Pneumatic Systems | |
Keywords: turbomolecular vacuum pump, pump parameter, gas pressure, suction side of the pump |
Automatic Control Systems for Heat and Power Installations and Ways to Improve Them
Authors: Markov V.An., Shatrov V.I. | Published: 19.10.2016 |
Published in issue: #5(110)/2016 | |
DOI: | |
Category: Power Engineering | Chapter: Heat Engines | |
Keywords: heat and power installations, combustion engines, diesel engines, automatic management systems, automatic control systems |