[2] Alemasov V.E., Dregalin A.F., Tishin A.P., Khudyakov V.A., Kostin V.N.,
Glushko V.P., eds. Termodinamicheskie i teplofizicheskie svoystva produktov
sgoraniya. Tom 2: Topliva na osnove perekisi kisloroda [Thermodynamic and
thermal-physical property properties of fire gases. Vol. 6. Fuels based on oxygen.].
Moscow, VINITI AN SSSR Publ., 1973. 489 p.
[3] Ponomarenko A. RPA: Tool for Rocket Propulsion Analysis. Thermal
Analysis of Thrust Chambers, 2012. Available at:
.
com/downloads/2/docs/RPA_ThermalAnalysis.pdf (accessed 16.04.2013).
[4] Veyalis S.A., Serpionova A.P., Linenko S.P. Film cooling. Gaseous film cooling.
Overview of international papers on Russian and foreign content press for 1957–
1977 years. GONTI-8 [State department of scientific and technical information],
1979, ser. IV, no. 41 (64), pp. 1–84 (in Russ.).
[5] Volchkov E.P. Pristennye gazovye zavesy [Wall-mounted gaseous film]. Novosibirsk,
Nauka Publ., 1983. 240 p.
[6] Arnold R., Suslov D.I., Haidn O.J. Film Cooling in a High-Pressure Subscale
Combustion Chamber. Journal of Propulsion and Rocket. 2010. Vol. 26, no. 5,
pp. 428–438.
[7] Druzhin A.N. Thermal and energy efficiency of sub- and supersonic gaseous film in
rocket engine with small propulsion.
Diss. kand. tekhn. nauk
[Cand. tech. sci. diss.].
Samara, 2002. 213 p.
[8] Arnold R., Suslov D.I., Haidn O.J. Experimental Investigation of Film Cooling with
Tangential Slot Injection in a LOX/CH
4
Subscale Rocket Combustion Chamber.
Trans. JSASS Space Tech.
, Japan, vol. 7, 2009.
[9] Kirchberger C., Schlieben G., Hupfer A., Kau H.-P., Martin P., Soller S. Investigation
on Film Cooling in a Kerosene/GOX Combustion Chamber.
AIAA Paper
, 2009,
no. 2009-5406.
[10] Chiaverini M.J., Sauer J.A., Munson S.M. Laboratory Characterization of Vortex-
Cooled Thrust Chambers for Methane/O
2
and H
2
/O
2
.
AIAA Paper
, 2005, no. 2005-
4131.
[11] Metzger D.E., Fletcher D.D. Evaluation of heat transfer for film-cooled turbine
components.
AIAA Paper
, 1969, no. 69–523.
[12] Sivasegaram S., Whitelaw J.H. Film cooling slots: the importance of lip thickness
and injection angle.
J. Mech. Eng. Sci.
, 1969, vol. 11, no. 1, pp. 22–27.
[13] Metzger D.E., Carper H.S., Swank L.R. Heat transfer with film cooling near
nontangential injection slots.
J. Eng. Power.
, 1968, vol. 90, no. 2, pp. 157–163.
[14] Eriksen V.L., Goldstein R.J. Heat transfer and film cooling following injection
through inclined circular tubes.
J. Heat Transfer.
, 1974, vol. 96, pp. 234–245.
[15] Kacker S.C., Whitelaw J.H. The dependence of the impervious wall effectiveness of
a two-dimensional wall jet on the thickness of the upper lip boundary layer.
Intern.
J. Heat Mass Transfer
, 1967, vol. 10, no. 11, pp. 1623–1624.
[16] Carlson L.W., Talmor E. Gaseous film cooling at various degrees of hot gas
acceleration and turbulence levels. Intern.
J. Heat Mass Transfer
, 1968, vol. 11,
no. 11, pp. 1695–1713.
[17] Finn E. Jorgensen. How to measure turbulence with hot-wire anemometers — a
practical guide. Denmark, Finn E. J¨orgensen – 2002, Dantec Dynamics A/S Publ.,
2002. 54 p.
Статья поступила в редакцию 16.04.2013
ISSN 0236-3941. Вестник МГТУ им. Н.Э. Баумана. Сер. “Машиностроение” 2014. № 1 91
