Influence of Friction and Elastic Shape Recovery on the Development of Corrugations under Oblique Plate Compression in Die Tooling

Authors: Tarasov V.A., Baskakov V.D., Boyarskiy D.S., Gerasimov N.V., Baburin M.A., Karnaukhov K.A. Published: 24.06.2023
Published in issue: #2(145)/2023  

DOI: 10.18698/0236-3941-2023-2-61-72

Category: Mechanical Engineering and Machine Science | Chapter: Manufacturing Engineering  
Keywords: corrugation, thinning, thickening, reshaping, workpiece contour


Reshaping the corner-shaped parts is an urgent technical problem making it possible to provide wall thickening at the top by compressing the artificially created excess metal in the shelves of the semi-finished product. However, shelf compression is accompanied by formation of the corrugations, which are partially deflected by the die planes and remain in the waviness form after the load is removed. Regularities in the corrugations development during the shelves’ compression were established and primarily dependence on the friction forces acting on the die boundary surfaces, which is necessary to comply with the requirements to the workpiece shelves waviness. The workpiece shelves’ compression was simulated by compression of a plate placed obliquely in the die cavity. It is shown that the number of corrugations increases with the compression stress growth. The corrugations amplitude also increases during compression. When corrugations and die walls are in contiguity, contact stresses and friction forces act on the deformable plate. This shields the compression force action in the plate behind the contact point. Localization of deformations in the area in front of the contact point contributes to an increase in the thickness of the angle-shaped workpiece during reshaping. It was established that the residual waviness was non-uniform over the plate, and was associated with the deformation area localization, and was proportional to the initial gap

Please cite this article in English as:

Tarasov V.A., Baskakov V.D., Boyarskiy D.S., et al. Influence of friction and elastic shape recovery on the development of corrugations under oblique plate compression in die tooling. Herald of the Bauman Moscow State Technical University, Series Mechanical Engineering, 2023, no. 2 (145), pp. 61--72 (in Russ.). DOI: https://doi.org/10.18698/0236-3941-2023-2-61-72


[1] Romanovskiy V.P. Spravochnik po kholodnoy shtampovke [Handbook on cold forging]. Leningrad, Mashinostroenie Publ., 1979.

[2] Ershov V.I., Chumadin A.S., eds. Listovaya shtampovka [Sheet stamping]. Moscow, MAI Publ., 1999.

[3] Chumadin A.S. Teoriya i raschety protsessov listovoy shtampovki [Theory and calculations of sheet forging]. Moscow, Eksposervis "VIP" Publ., 2014.

[4] Wanintradul C., Golovashchenko S.F., Gillard A.J., et al. Hemming process with counteraction force to prevent creepage. J. Manuf. Process., 2014, vol. 16, no. 3, pp. 379--390. DOI: https://doi.org/10.1016/j.jmapro.2014.04.003

[5] Kuwabara T. Advances in experiments on metal sheets and tubes in support of constitutive modeling and forming simulations. Int. J. Plast., 2007, vol. 23, no. 3, pp. 385--419. DOI: https://doi.org/10.1016/j.ijplas.2006.06.003

[6] Tarasov V.A., Baskakov V.D., Baburin M.A., et al. Engineering estimation of the error of bending of angle blanks in a tool die. Russ. Metall., 2019, vol. 2019, no. 13, pp. 1460--1465. DOI: https://doi.org/10.1134/S0036029519130378

[7] Popov E.A. Osnovy teorii listovoy shtampovki [Fundamentals of sheet metal forming theory]. Moscow, Mashinostroenie Publ., 1968.

[8] Tarasov V.A., Baskakov V.D., Baburin M.A., et al. Thinning of wall in vertex of angled part during bending in tool die. Tekhnologiya metallov, 2021, no. 4, pp. 22--27 (in Russ.).

[9] Boyarskiy D.S., Baburin M.A., Baskakov V.D., et al. [Method of approximate estimation of corner shape part thickening at bending in tool stamp.]. XLIV Akademicheskie chteniya po kosmonavtike. T. 2 [XLIV Academic Readings on Cosmonautics. Vol. 2]. Moscow, Bauman MSTU Publ., 2020, pp. 399--401 (in Russ.).

[10] Mantusov M.N. Stamping of curved flanges of sheet parts with elastomer with the imposition of tangential compression. KShP. OMD. [Forging and Stamping Production. Processing of Materials by Pressure], 2021, no. 4, pp. 17--22 (in Russ.).

[11] Baburin M.A., Vodyanskiy M.L., Grachev A.V. Sposob izgotovleniya profiley preimushchestvenno W-obraznogo secheniya [Method for forming, mainly shapes with W-like cross section]. Patent RU 22673773. Appl. 05.03.2004, publ. 10.01.2006 (in Russ.).

[12] Feodosyev V.I. Soprotivlenie materialov [Strength of materials]. Moscow, Nauka Publ., 1972.

[13] Rabotnov Yu.N. Soprotivlenie materialov [Strength of materials]. Leningrad, Nauka Publ., 1962.

[14] Parshin V.S., Karamyshev A.P., Nekrasov I.I., et al. Prakticheskoe rukovodstvo k programmnomu kompleksu DEFORM-3D [Practical guide for DEFORM-3D software complex]. Ekaterinburg, UrFu Publ., 2010.

[15] Tarasov V.A., Baskakov V.D., Baburin M.A., et al. Approximation of deformation diagrams of steels by their mechanical characteristics. Chernye metally [Ferrous Metals], 2020, no. 8, pp. 59--63 (in Russ.).

[16] Boyarskiy D.S., Tarasov V.A., Baburin M.A., et al. Numerical analysis of corrugation development during oblique compression of a plate when manufacturing angle metal parts. Izvestiya vysshikh uchebnykh zavedeniy. Mashinostroenie [BMSTU Journal of Mechanical Engineering], 2022, no. 9 (750), pp. 92--99 (in Russ.). DOI: http://dx.doi.org/10.18698/0536-1044-2022-9-92-99